A improve new development of the Data East Solid State Flipper Board 520-5033-00, 520-5076-00 and 520-5080-00. Our PinLED Solid State Flipper Board 40001 is a replacement for defective original boards. The board has brand new innovations and has this four advantages:
-
New development of the driver section
-
Combined Solid State Flipper Board - Replacement for ALL original Data East Solid State Flipper Boards.
-
Increase the power of the flipper coils
-
Introduction of new fuse clips.
It is possible to go new ways in circuit board design with new parts. We use the most modern parts on this board and this will help us to eliminate all of the bad failures that you can find on the old boards.
-
New development of the driver section: We use MOSFET transistors therefore we were able to reduce the number of parts considerably. MOSFETs are able to switch a high amount of current with a very small on-resistance. They have a lot of advantages towards the original used TIP36C transistors. The TIP36C are often broken because of an malfunction of the flipper switches or a bad coil. And if the coil conduct a longer period of time, the transistor dies the "heat death". The MOSFETs have the big advantage that they normally can't get damaged even with bad coils or incorrect signals from the flipper switches. We also made stronger wires in the driver section on the board, so that burned out wires belong to the past.
-
Combined Solid State Flipper Board - Replacement for ALL original Data East Solid State Flipper Boards: We have add all different versions of the board generation on our new board. The original 2- or 3 flipper Data East Solid State Flipper Boards are combined on our new Board. It doesn't matter with game you have (first version without E.O.S switches or the later 2- or 3 flipper versions with E.O.S switches. We use a dip switch and different connectors for the several versions.
-
Increase the power of the flipper coils: With the new PinLED Solid State Flipper Board installed the power of the flipper coils will increase. This happens because of the smaller on-resistance of the MOSFETs. Normal transistors have a larger on-resistance that decreases the power of the flipper coils. With our board installed you can get all the steep ramps that the original Data East Solid State Flipper Board fails.
-
Introduction of new fuse clips: Are you tired of broken fuse clips and direct soldered fuses? The original fuses clips are often broken because they are too weak. We use new 5x20mm fuse clips. They have a better quality and they are stronger...
The PinLED Solid State Flipper Board 40001 is "Plug and Play". All plugs are the same like the original. The installation takes only 5 minutes! You will find a detailed installation instruction on our support site.
The next two pictures show the new PinLED Solid State Flipper Board...
 |
 |
You can use our PinLED Solid State Flipper Board for the following pinballs:
| Flipper | 520-5033-00 | 520-5076-00 | 520-5080-00 |
| ABC Monday Night Football | a | ||
| Apollo 13 |
|
a | |
| Back To The Future | a | ||
| Batman | a | ||
| Batman Forever | a | ||
| Baywatch (es werden 2 Stück benötigt) | a | ||
| Checkpoint | a | ||
| Golden Eye | a | ||
| Guns N' Roses | a | ||
| Hook | a | ||
| Jurassic Park | a | ||
| Last Action Hero | a | ||
| Lethal Weapon 3 | a | ||
| Mary Shelley's Frankenstein | a | ||
| Maverick | a | ||
| Phantom Of The Opera | a | ||
| Playboy 35th Anniversary | a | ||
| Robocop | a | ||
| Rocky & Bullwinkle & Friends | a | ||
| Star Trek 25th Anniversary | a | ||
| Star Wars | a | ||
| Tales From The Crypt | a | ||
| Teenage Mutant Ninja Turtles | a | ||
| The Simpsons | a | ||
| The Who's Tommy | a | ||
| WWF Royal Rumble | a |
Please note our Warranty Provisions!
go back